男人天堂av东京热,日韩欧美国产一级片,欧洲亚洲一区二区三区,久久久久亚洲AV成人网人人软件

產品展示
首頁 > 產品展示 > > 其他檢測儀器 > TC-500 氧氮聯合測定儀

TC-500 氧氮聯合測定儀

簡要描述：簡單說明：TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

  • 產品型號：TC-500
  • 廠商性質：生產廠家
  • 更新時間：2024-10-08
  • 訪  問  量：2160
詳情介紹

詳細說明:

TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

Determination of Oxygen and Nitrogen in
Reactive/Refractory Metals and Their Alloys*
 
Approval
ASTM E-1409 Oxygen Determination in Titanium and Titanium Alloys
ASTM E-1569 Oxygen Determination in Tantalum
ASTM E-1937 Nitrogen Determination in Titanium and Titanium Alloys
 
Sample Preparation
A clean representative sample is required in order to obtain optimum results. Solid samples can be leached in suitable acid or abraded with a clean file, rinsed in acetone, and dried with warm air. Refer to ASTM methods above for further details.
 
Accessories
782-720 Crucible; 782-721 Electrode Tip; 502-344 UHP Nickel
Baskets; 501-073 Graphite; 503-032 Glass Accelerator Scoop;
501-059 Tin Capsules—for powdered samples. （Additional steps required for powdered samples are noted in parenthesis.）
 
Calibration Standard
LECO 501-320 Titanium Pin, 502-047 Zirconium Pin, NIST, or other suitable reactive/refractory metal standard.
 
Method Parameters
Analysis Parameters
Outgas Cycles                           2
Analysis Delay （seconds）             20
Analysis Comparator                 1
Analysis Type                              Auto
 
Element Parameters                  Oxygen           Nitrogen
Minimum Time （seconds）
35
55
Integration Delay （seconds）
5
15
Comparator Level （%）
1
1
 
Furnace Parameters
Furnace Control Mode             Power
Purge Time （seconds）                    15
Outgas Time （seconds）                20
Cool Time （seconds）                    5
Outgas Power （Watts）                 6300
Analyze Power （Watts）                5300
 
 
 
 
 


 

*This includes Ti, Zr, W, Mo, Ta, Nb, Hf, and their alloys.

 
TC500


 

 
Typical Results
 
 
 
Titanium Pin
Mass （g）
Oxygen （%）
Nitrogen （%）
 
0.1135
0.1808
0.0189
 
0.1133
0.1843
0.0194
 
0.1134
0.1831
0.0184
 
0.1138
0.1819
0.0188
 
0.1133
0.1821
0.0195
 
0.1131
0.1829
0.0185
 
0.1134
0.1833
0.0191
 
0.1143
0.1849
0.0194
 
0.1125
0.1837
0.0189
 
0.1072
0.1830
0.0191
 
Average
0.1830
0.0190
 
Std. Dev.
0.0012
0.0004
 
Zirconium Wire
 
Mass （g）
 
Oxygen （%）
 
Nitrogen （%）
 
0.1067
0.1246
0.0017
 
0.0978
0.1273
0.0017
 
0.1180
0.1246
0.0019
 
0.1097
0.1235
0.0014
 
0.1141
0.1272
0.0017
 
0.1017
0.1226
0.0018
 
0.1140
0.1269
0.0020
 
0.0987
0.1239
0.0020
 
0.1015
0.1233
0.0022
 
0.1197
0.1270
0.0020
 
Average
0.1251
0.0018
 
Std. Dev.
0.0018
0.0002
 
Procedure
 
 
 
1.   Determine the blank as follows:
a.   Enter the "blank" ID code with a 1.0000 g weight in the weight stack.
b.   Press the loader control switch, the sample loader will open.
c.   Place one 502-344 UHP Nickel basket into the loading head using clean tweezers.
（Place a 501-059 Tin capsule into the Nickel basket before placing it in the loading head.）
d.   Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
e.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
f.    Place ~0.05 g 501-073 into the bottom of a 782-720 crucible.  ~0.05 g is approximay a ¼ full
503-032 glass accelerator scoop.
g.   Place the crucible on the lower electrode.
h.   Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
i.    Repeat steps 1a through 1h at least four more times.
j.    Enter blank following routine outlined in operator's instruction manual.
2.   Calibrate the instrument as follows:
a.   Weigh the calibration sample. （Weigh the calibration sample into the tin capsule.）
b.   Enter the calibration sample ID code and sample weight in the weight stack.
c.   Place the calibration sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the calibration sample/nickel basket （capsule） into the loading head using clean tweezers.  Make sure that the calibration sample （capsule） stays in the basket and the basket
stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
continued on page 3


 

Procedure （continued from page 2）
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
k.   Repeat steps 2a through 2j a minimum of three times.
l.    Complete a calibration by following the auto calibration procedure as outlined in the operator's instruction manual.
m.  Verify the calibration by analyzing the calibration sample again.  It should fall within the expected tolerances.  If not, repeat steps 2a through 2l again.
3.   Analyze the samples as follows:
a.   Weigh ~0.1 g sample. （Weigh the sample into the tin capsule.）
b.   Enter the sample ID code and sample weight in the weight stack.
c.   Place the sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the sample/nickel basket （capsule） into the loading head using clean tweezers.
Make sure that the sample （capsule） stays in the basket and the basket stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
 
Theory of Operation
The TC500 is a microprocessor-based, software-controlled instrument that measures both nitrogen and oxygen in a wide variety of metals, refractories, and inorganic materials. The inert gas fusion principle is employed. A weighed sample, placed in a high-purity graphite crucible, is fused under a flowing helium gas stream at temperatures sufficient to release oxygen, nitrogen, and hydrogen. The oxygen in the
sample, combines with the carbon from the crucible to form carbon monoxide. The nitrogen present in
the sample releases as molecular nitrogen, and any hydrogen present is released as hydrogen gas. The helium carries the sample gases through heated rare earth copper oxide which converts carbon
monoxide to carbon dioxide （CO2） and hydrogen to water （H2O）. The nitrogen passes through
unchanged. The gases are then passed through a CO2  infrared （IR） cell where the oxygen is measured as
CO2. CO2  and H2O are then removed by a Lecosorb/Anhydrone trap, while the nitrogen passes through
to a thermal conductivity （TC） cell for determination.


 

TC500 Flow Diagram
 
 
 
 
 

留言框

  • 產品：

  • 您的單位：

  • 您的姓名：

  • 聯系電話：

  • 常用郵箱：

  • 省份：

  • 詳細地址：

  • 補充說明：

  • 驗證碼：

    請輸入計算結果（填寫阿拉伯?dāng)?shù)字），如：三加四=7

技術支持：化工儀器網   sitemap.xml   管理登陸
©2025 版權所有：寧波市鄞州瑾瑞儀器設備有限公司   備案號：浙ICP備14028217號-3

浙公網安備33020402000311號
韩国最新伦理片电影| 成全免费高清观看| 欧美午夜性春猛交ⅩXXX| 亚洲熟女一区二区三区| 久久久无码精品亚洲日韩按摩| 亚洲 自拍 另类 欧美 综合| 欧美熟妇精品久久久久久| 中国BGMBGMBGM老头和老妇| 9久9久女女免费精品视频在线观看| 亚洲欧洲自拍拍偷午夜色无码| 夜夜爱夜夜做夜夜爽| 成 人 色综合 综合网站| 精品成人一区二区三区免费视频| 亚洲1区2区3区橡胶防水卷材| 手机看片久久国产免费 | 4399在线观看免费韩国中文| 最新国产美女一区二区三区| 亚洲蜜桃V妇女| 亚洲熟妇另类久久久久久| 一区二区三区国产好的精华液| 特黄熟妇丰满人妻无码| 99精品国产福利免费一区二区| 亚洲欧洲日韩| 国产拍拍拍无码视频免费| 日韩精品欧美中文字幕| 亚洲AV成人午夜亚洲美女| 国产在线视频一区| 久久国产乱子伦精品在| 限制级电影在线播放| 99久久无色码中文字幕人妻蜜柚| 国产原创对白在线观看精品| 亚洲av日韩综合一区尤物| 中文字幕日产乱码芒果| 亚洲日韩一区二区一无码| 久久www免费人成精品香蕉| 欧洲无码精品A码无人区| 国产亚洲欧美一区久久久在| 日韩 欧美 在线| 岳好紧好湿夹太紧了好爽矜持| 伊人色综合一区二区三区| 久久精品国产欧美日韩|